Aluminum Coils for Lightweight and Corrosion-Resistant Use

We are dedicated to providing high-quality steel products complemented by trustworthy services and a global presence.

English

Home // News

News Center

Oct. 06, 2026

Q235 vs Q355 Steel: Strength, Applications, and Cost Comparison

Q235 is a lower-strength carbon structural steel with a minimum yield strength of approximately 235 MPa in thin sections, while Q355 is a higher-strength low-alloy structural steel reaching about 355 MPa at comparable thickness. Q235 normally costs less and is straightforward to fabricate; Q355 supports heavier loads, thinner sections, and weight reduction when the design and approval documents

Oct. 05, 2026

Common Steel Sheet Surface Defects and How to Identify Them

Steel sheet surface defects are visible or near-surface irregularities that can reduce appearance, corrosion resistance, coating adhesion, weldability, fatigue life, or dimensional usability. Common Steel Sheet Surface Defects and How to Identify Them requires more than a quick visual check: inspectors should evaluate appearance, location, direction, repetition, depth, texture, and response to

Oct. 02, 2026

Galvanized Steel Coating Thickness Explained: Z30 to Z275

Galvanized steel coating thickness refers to the amount of zinc applied to a steel surface for corrosion protection. In continuous galvanized sheet designations, Z30 through Z275 generally indicate total zinc coating mass in grams per square meter across both sides, not micrometers measured on one surface. As the Z value increases, the approximate zinc thickness and expected corrosion-resistance

Oct. 01, 2026

Galvanized vs Color-Coated Roofing Sheets: How to Choose

Galvanized sheets are usually the lower-cost choice for utility buildings, while color-coated sheets add a painted barrier, better appearance, and more design flexibility. The right option depends on zinc or paint coating specifications, sheet thickness, climate exposure, maintenance access, expected service life, and total ownership cost rather than purchase price alone.

Oct. 15, 2026

Q235 vs ASTM A36 Steel: Key Differences Buyers Should Know

Q235 and ASTM A36 are widely used structural carbon steel grades, but they are not automatically interchangeable. Q235 vs ASTM A36 steel involves differences in standard systems, chemical composition, yield strength, tensile strength, impact-testing requirements, product thickness, certification, and purchasing risk. The correct choice depends on the governing design code and the documents

Oct. 14, 2026

Corrugated vs Trapezoidal Roofing Sheets: Which Is Better?

Trapezoidal sheets generally suit low-slope, long-span, high-load, and heavy-rain projects, while corrugated sheets suit steeper roofs, curved sections, traditional appearances, smaller structures, and lower budgets. The deciding factors are roof pitch, unsupported span, purlin spacing, rainfall intensity, wind exposure, fastening method, lap detailing, installer capability, and total installed

Oct. 13, 2026

What Is the Best Thickness for Steel Roofing Sheets?

The best thickness for steel roofing sheets depends on the roof profile, climate, structural support, installation method, and required service life. In most residential projects, 26 gauge steel roofing is the practical starting point, while 24 gauge is preferred for standing seam systems, high-wind locations, heavy snow, and buildings where dent resistance matters. 29 gauge can reduce material

Oct. 12, 2026

Why Cold Rolled Steel Is Widely Used for Stamping Parts

Cold rolled steel is widely used for stamping parts because it combines tighter dimensional tolerances, smoother surface finish, consistent thickness, and increased strength. Compared with hot-rolled steel, it is usually better suited to precision components, visible surfaces, painted parts, and assemblies requiring repeatable geometry. The correct choice still depends on forming severity,

Oct. 09, 2026

How to Prepare Cold Rolled Steel Sheet for Painting and Coating

Cold rolled steel has a smooth, dimensionally consistent surface, but it is not automatically ready for paint or coating. How to Prepare Cold Rolled Steel Sheet for Painting and Coating depends on the sheet thickness, mill oil, storage condition, fabrication residue, corrosion level, coating system, and intended exposure. A reliable process normally includes surface inspection, degreasing,

1 2 3 4 5 6 7 8 ... 15 16 >

SHANDONG ZZC IMPORT AND EXPORT CO.,LTD

E-mail:

sdzzcsteel@gmail.com

sdzzcella@gmail.com

Mobile:

+86 137 0635 4288

Tel.:

+86 635 8800 366

Fax:

+86 635 8800 366

WeChat:

zzcsteel

WhatsApp:

+8613706354288

Add.:

Room 2306, Building 12, Xingguang International Financial Center, Dongchang East Road, Development Zone, Liaocheng City, Shandong Province, China

Navigation

Home

About Us

Products

Application

FAQ

News

Product

Steel Coils

Steel Pipes & Tubes

Steel Sheet

Other Products

Request a Quote

Submit

+8613706354288

Ella Lee

Ella Lee

Ella Lee: zzcsteel

Chat with Us

Welcome ! Please leave your contact information, we will contact you as soon as possible.